carbon monoxide detector 30 ppm image
Chris Marm
I have 2 carbon monoxide detectors. one behind my dryer and one upstairs by the bedrooms. one was beeping every 30 seconds which i believe means that there is a problem with the device, however i moved the one from upstairs into the spot where the alarming one was and when i press the test button a reading of 210 ppm comes up? what should i do?
Answer
http://en.wikipedia.org/wiki/Carbon_monoxide_poisoning
Readings above 100 ppm are dangerous.
I would turn down the heat (preferably off, if not too cold) and leave the house, and have a professional test it.
Assuming this is a standalone house, I assume that you have a gas furnace or water heater malfunctioning in your home.
I had first wondered if you had a malfunctioning unit - I had one once - but having your other monitor show that reading makes me want you to be safe.
http://en.wikipedia.org/wiki/Carbon_monoxide_poisoning
Readings above 100 ppm are dangerous.
I would turn down the heat (preferably off, if not too cold) and leave the house, and have a professional test it.
Assuming this is a standalone house, I assume that you have a gas furnace or water heater malfunctioning in your home.
I had first wondered if you had a malfunctioning unit - I had one once - but having your other monitor show that reading makes me want you to be safe.
Carbon Monoxide - Possible Sources?
Melissa
We live in the middle of a block of rowhomes in Baltimore City. For the second time in a month, the CO alarms have gone off at the houses on either side of us. This time, I was the only one of all of us who was awake. I had used hot water for a shower and washed a few dishes about an hour before. Firefighters checked our three homes, as well as the two other houses adjoining my neighbors. Readings were 30 ppm in one of the alarm houses and 90 in the other; zero in my home and the two other neighbors. When the firefighter turned on the hot water and held the meter next to my water heater for ten minutes, the highest reading he got was 8 ppm. We immediately replaced our CO alarm with a detector with a constant display, which is still showing 0 ppm after two hours in the room with the furnace (not running) and the water heater. The alley behind our homes is too narrow for a car or truck. We are at a loss for the source. Any ideas?
We have a Weber kettle grill and a Weber smoker, which we haven't used yet this year because we are having a particularly rainy summer. The alarm houses have gas grills, but this was 4.30 in the morning. Even if they both happened to have faulty tanks, they would have had to have been lit sometime around the time of the alarm, right? The 30 ppm house was gutted and rebuilt last year. The contractors were questionable, but the HVAC sub-contractors are reputable, as far as we know.
Answer
CO comes only from incomplete combustion of hydrocarbons (including charcoal), and not from any other sources. It is also lighter than air, and so may build up well away from where it is generated.
As you are in a row-house - if you share a chimney with a neighbor, and their flue is partially or entirely blocked, that CO may penetrate into your flue/house from next door. It is also possible that you may even share a flue, although that is unlikely.
Other sources might include a charcoal-fired grille near an open window or intake fan that might draw CO into the house. A partially blocked flue - or one that is blocked intermittently by a nest, or a loose brick or something similar such that the CO builds up at odd times.
I suggest that you check all your flues - all of them - and make sure that they are clear, free of any obstructions and draw properly. I suggest that while you are at it, you check any flues on your common walls and any that may vent near any of your windows at any level. You should also (if at all possible), see if your neighbors might be operating a charcoal device such as even a small hibachi inside their house - or may be using some other device such as a still, retort or other equipment that uses a fairly large flame, but may be in an area with restricted air intake.
NOTE ALSO: if you have your water heater in a tight basement, closet or other area without free access to outside (fresh) air in quantity, it might operate perfectly normally with the fire department standing around (all the doors open), but when you close the doors and restrict air-flow to it, start to produce CO in quantity.
You have done the right thing with the detector. Good luck with it in general!
CO comes only from incomplete combustion of hydrocarbons (including charcoal), and not from any other sources. It is also lighter than air, and so may build up well away from where it is generated.
As you are in a row-house - if you share a chimney with a neighbor, and their flue is partially or entirely blocked, that CO may penetrate into your flue/house from next door. It is also possible that you may even share a flue, although that is unlikely.
Other sources might include a charcoal-fired grille near an open window or intake fan that might draw CO into the house. A partially blocked flue - or one that is blocked intermittently by a nest, or a loose brick or something similar such that the CO builds up at odd times.
I suggest that you check all your flues - all of them - and make sure that they are clear, free of any obstructions and draw properly. I suggest that while you are at it, you check any flues on your common walls and any that may vent near any of your windows at any level. You should also (if at all possible), see if your neighbors might be operating a charcoal device such as even a small hibachi inside their house - or may be using some other device such as a still, retort or other equipment that uses a fairly large flame, but may be in an area with restricted air intake.
NOTE ALSO: if you have your water heater in a tight basement, closet or other area without free access to outside (fresh) air in quantity, it might operate perfectly normally with the fire department standing around (all the doors open), but when you close the doors and restrict air-flow to it, start to produce CO in quantity.
You have done the right thing with the detector. Good luck with it in general!
Powered by Yahoo! Answers
